Current location:Home > news > Troubleshoot
The importance of the 4x4 tact switch

栏目:Troubleshoot

发布时间:2021-01-13 09:49:31

4x4 tact switches can be divided into low-voltage molded case key switches and low-voltage frame type key switches. The former is used for low-voltage and small current, and the latter is used for low-voltage and high-current. The low-voltage molded case circuit breaker is commonly known as automatic key switch.




Several definitions in the Chinese national standard GB14048.2 for 4x4 tact switches (mandatory standard, if you want to learn more about low-voltage circuit breakers, just look at this standard):.




1. Circuit breaker: a mechanical switching device that can switch on, carry and break current under normal circuit conditions, and can also switch on under specified abnormal circuits (such as short circuits), and carry a certain period of time and breaking current.




2. Molded case circuit breaker: a circuit breaker with a shell made of molded insulating material as an integral part of the circuit breaker.




3. Air circuit breaker: a circuit breaker whose contacts are opened and closed in atmospheric pressure air.




4. Convenient and safe to use. The product can be easily turned on or off with a touch switch for use. When it is turned on and off, it should not significantly hinder the movement or movement of people or objects in the building, and it should be able to facilitate the cleaning and cleaning of the ground. , The ground socket should have different protection levels to adapt to the different requirements of the use environment to ensure the safe use of users.




The 4x4 light touch switch is reset after power failure, that is, the locking mechanism should be related to the power supply. The finished product does not seem to be available, because this requirement can be achieved by a circuit composed of a general button switch and a relay.




But if only one relay (or contactor) is used, a set of normally open contacts is used to control the power supply of the working coil of the relay (contactor), and the relay weighing iron is used as the switch button. After pressing the weighing iron, the relay controls The contact of the coil is closed, the coil is energized, the relay remains closed (self-locking), and the remaining contacts control other circuits.




What matters should be paid attention to when using the circular tact switch.




Tact switch 1. When soldering the tact switch terminal, if a load is applied to the terminal, there will be loosening, deformation and deterioration of electrical characteristics due to different conditions. Please pay attention when using it. 2. Use a through-hole printed circuit board. And the circuit boards other than the recommended ones, due to the influence of thermal stress, please fully confirm the soldering conditions in advance. 3. When performing two soldering, please do it after the first soldering part returns to normal temperature. Continuous heating may deform the periphery, loosen terminals, fall off, and reduce electrical characteristics. 4. Regarding the setting of welding conditions, it is necessary to confirm the actual mass production conditions. 5. Products designed and manufactured on the premise of DC resistance load, use others For load [inductive load, capacitive load], please confirm separately.




6. For the mounting holes and patterns of the printed circuit board, please refer to the recommended dimensions in the product drawings. 7. The switch should be used for the structure of the switch directly operated by humans. Please do not use it for the mechanical detection function of the touch switch. 8. When you touch the switch, if you apply more than the specified load, the switch may be damaged. Please be careful not to apply more than the specified force on the switch. 9. Please avoid the use of pressing the operating part from the side. 10. For the flat shaft For the rod type, try to press the center of the switch. For the hinge structure, the position of the shaft will move when pressed, so please pay special attention.




11. After the switch is installed, when the adhesive of other parts passes through the regenerative hardening furnace, please contact a professional. 12. If the surrounding materials of the switch using the switch produce corrosive gas, it may cause contact Defects and other phenomena, so please fully confirm in advance. 13. The carbon contact point has the characteristic of changing the contact resistance of the pushing load. When used in a voltage divider circuit, please use it after sufficient confirmation. 14. About the sealed type For other models, please pay attention to the intrusion of foreign matter.


Service Hotline+86-135-3830-2000

Landline:+86-0769-83666259

Tianmei Industrial Zone, Huangjiang Town, Dongguan City